Baseline-systems BaseStation 3200 Bedienungsanleitung Seite 86
- Seite / 102
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
BaseStation 3200 Advanced Irrigation Controller Manual
Pause Conditions
A variety of conditions will cause the controller to pause watering, either
by specific programs or the entire controller. When one or more pause
conditions occur, the Pause Condition reports describe the reasons for the
pause conditions.
The following pause conditions can occur on the BaseStation 3200.
BL-Commander
(handheld
radio)
•
All programs will be paused while running a zone using the remote handheld radio – all
programs resume when the zone is shut off.
• Press CLR to terminate the manual zone.
• Automatically cleared when the zone is done.
BaseManager
(central control
software)
•
Normal operation continues while the controller is accessed by BaseManager.
• Press CLR to terminate the BaseManager connection.
• Automatically cleared when BaseManager logs off.
Event Day
• An event day stops all watering and keeps programs from starting.
• Press CLR to terminate the event day.
• Automatically cleared when the event day ends.
Flow Devices
• A high-flow shutdown or an over-budget shutdown stops the system from using the
specific flow device.
• Press CLR to reset a high flow shutdown condition.
• Pressing CLR does not clear an over-budget condition. Change the budget or wait until
next month.
• Not automatically cleared – the user must clear this pause condition.
Flow Switch
• An open jumper or flow switch stops all watering and keeps all programs from starting.
• Pressing CLR does not reset this condition. Replace the jumper or reset the flow switch
hardware.
• Not automatically cleared – the user must clear this pause condition.
Low
Temperature
• When the temperature drops below 38
◦
F, the system will pause all watering.
• Pressing CLR does not reset this condition. You must wait until the temperature rises.
• Automatically cleared with higher temperatures.
Pause biCoder
•
A pause biCoder will pause watering on specific programs.
• Pressing CLR resets the pause condition before the delay time has elapsed.
• Automatically cleared at end of the delay time.
Page 78
- BaseStation 3200 1
- Revision 2 2
- Table of Contents 3
- Page vi 8
- 1 – INTRODUCTION 9
- Soil Moisture Content 10
- Choosing the Sensor Location 13
- Burying the biSensor 13
- Turf Grass 14
- Trees and Shrubs 14
- Watering Strategies 15
- Understanding Soak Cycling 17
- Distribution Uniformity 18
- 2 – SYSTEM COMPONENTS 19
- Two-Wire Devices 20
- C-series Wall Mount Cabinets 22
- Connecting Power and Ground 23
- P-series Pedestal Cabinets 24
- 3 – WIRING GUIDELINES 26
- Expanding with Two-Wire 28
- Two-Wire Installation 29
- Two-Wire Serial Numbers 30
- Wire Layout 31
- Wire Burial 31
- Installing Two-Wire Devices 32
- Installation Instructions 33
- To the two 34
- Wiring a Pump Start Relay 35
- Wiring a Flow Device 35
- Wiring a Flow Device +NOMV 36
- Wiring a Water Meter 37
- Pause Devices 38
- Removing a Two-Wire Device 40
- On-Screen Help 42
- Auto Run Main Screen 42
- Status Colors 43
- On-Screen Reports 43
- 5 – CONFIGURING DEVICES 44
- Searching for biSensors 45
- Assigning biCoders to Zones 46
- Understanding Zone Statuses 47
- Configuring Other Devices 48
- 6 – INITIAL PROGRAMMING 50
- Setting Up a Timed Zone 51
- Assigning a Primary Zone 52
- To assign a primary zone 53
- Using Soak Cycles 54
- Setting Up Programs 55
- Prerequisites 57
- Instructions 58
- Lower Limit 61
- Upper Limit 62
- Setting Up Event Days 64
- Configuring a Flow Device 65
- Mainline Setup 67
- Managing Concurrent Zones 69
- Learning Flow 70
- Learning the Flow by Zone 71
- 8 – MANUAL OPERATIONS 73
- Watering Manually 74
- Manually Running All Zones 75
- Setting Up a Rain Delay 77
- Setting the System to OFF 77
- 9 – SYSTEM MANAGEMENT 78
- Using the USB Data Functions 79
- Exporting Log Files 80
- Importing Log Files 80
- Using the Clear All Option 82
- Zone Status 83
- Program Status 84
- Moisture Sensor Data 85
- Water Used 85
- Pause Conditions 86
- Operator Messages 87
- Viewing Exported Log Files 88
- 11 – TROUBLESHOOTING 90
- Testing All Devices 92
- 12 – APPENDIX 95
- Page 90 98
- Glossary of Terms 99
Verwandte Produkte und Handbücher für Sensoren Baseline-systems BaseStation 3200
(9 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.354 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern