Baseline-systems BaseStation 1000 Bedienungsanleitung Seite 39
- Seite / 122
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
BaseStation 1000 Irrigation Controller Manual
8. Press the OK button. The serial number of the device that you selected in the Action column
now displays next to the number in the Event Switch column.
Note: If the search found multiple devices, the next serial number in the Action column is
automatically selected. Press the
or
button in the Event Switch column to move to the
next number that you want to assign, and then press the OK button.
9. Continue until you have assigned all your switch devices to their numbers.
Setting Up Event Switches
After you assign a device to a specific use in the BaseStation 1000 system, the device is
automatically enabled. You can disable that device if you want to take it out of service temporarily,
and then you can enable it again when necessary.
1. Press the Search & Assign button. The Search & Assign menu displays.
2. Press the
or
button to highlight the Event Switch option, and then press the OK button
to select it. The Event Switch screen displays.
3. Press the
or
button to highlight the Device Setup option, and then press the OK button.
The E. Switch Device Setup screen displays.
4. Press the
or
button to highlight the switch device number in the left column, and then
press the
button to move to the Enabled field.
If the device is currently enabled, a checkmark displays in the Enabled field. Press the +
or – button to remove the checkmark.
If the device is currently disabled, there is no checkmark in the Enabled field. Press the
+ or – button to replace the checkmark.
5. Continue until you have configured the settings for all your event switch devices.
Searching For and Assigning Air Temperature Sensors
1. Press the Search & Assign button. The Search & Assign menu displays.
2. Press the
or
button to highlight the Temperature Sensor option, and then press the OK
button to select it. The Temperature Sensor screen displays.
3. If the Device Assignment option is highlighted, press the OK button to select it. If Device
Assignment is not highlighted, press the
or
button to highlight it, and then press the OK
button. The Temp. Assignment screen displays.
4. When the Search option in the Action column is highlighted, press the OK button to search
for air temperature sensors.
When the controller finds the devices, their serial numbers display in the Action column.
5. Press the
or
button to move through the list of devices in the Action column. Highlight
the serial number of the air temperature sensor that you want to assign.
6. Press the
button to move to the Temp. Sensor column.
Page 33
- BaseStation 1
- Table of Contents 3
- 1 – Introduction 7
- Soil Moisture Content 8
- Choosing the Sensor Location 11
- Burying the biSensor 12
- Trees and Shrubs 13
- Watering Strategies 14
- Understanding Soak Cycling 16
- Intelligent Soak Cycles™ 17
- Distribution Uniformity 18
- Recommendations 20
- 2 – System Components 21
- Remote Communication Options 22
- Two-Wire Devices 23
- Maximum Concurrent Valves 25
- C-Series Wall Mount Cabinets 26
- Connecting Power and Ground 27
- P-Series Pedestal Cabinets 28
- On-Screen Help 30
- Zone Status Report 30
- BaseManager Message 31
- 4 – Configuring Devices 32
- Setting Up Zones 33
- (biSensors) 36
- Setting Up Moisture Sensors 36
- Setting Up Flow biCoders 37
- Setting Up Event Switches 39
- Unassigning a Device 40
- Restarting the Controller 42
- Setting Up Programs 44
- Setting Up a Rain Delay 62
- Setting Up Event Days 63
- Enabling Flow Variance 68
- Learning Flow 70
- Learning the Flow by Zone 71
- 7 – Manual Operations 72
- 8 – System Setup 78
- Controller 86
- Adding Expansion Modules 93
- Understanding Zone Statuses 95
- Viewing Operator Messages 98
- Viewing Moisture Graphs 100
- 10 – Testing Devices 102
- Testing Flow Sensors 106
- Testing Event Switches 106
- Testing the Two-Wire 107
- Testing All Devices 108
- Troubleshooting Manually 110
- 11 – Appendix 111
- Based Watering 114
- Configuring a Booster Pump 115
- Page 112 118
- Glossary of Terms 119
Verwandte Produkte und Handbücher für Sensoren Baseline-systems BaseStation 1000
(12 Seiten)Samsung SP-D400 manuali
Manuali dei proprietari e guide per l'utente per Lettori CD Samsung SP-D400.
We fornisce manuali pdf Samsung SP-D400 per scaricare gratuitamente in base al tipo di documento:
Kommentare zu diesen Handbüchern